After a period of competition or practice, the golf club will experience some grip or grip problems. If equipped with the following knowledge, golfers can repair themselves without bringing them to the mechanic. So, how to reshaft a golf club? The following article can answer this question for you.
How is the importance of golf shafts?
Choosing the right shaft installed on the club will give you a good shot of stability. It gives you the best chance of hitting the center of the clubface, enabling the ball to be launched to the correct angle with optimal geometry and high efficiency for hitting on target and with sufficient distance.
Shaft is like an actuator in a car, and even though it’s not an engine, it is extremely important. If you drive a truck, you always want to ensure that the drivetrain delivers the correct motion for your particular requirements.
If you install the wrong sports car transmission, for example, your car will have trouble transferring to handle the heavy loads of trucks, and your truck driving skills have accumulated over the years. It is also impossible to do much work on a truck and install another vehicle’s transmission by mistake.
This is similar to choosing the correct shaft for your swing technique because some shaft performance variations can affect your ability to hit the ball effectively. Choosing the correct shaft is not as simple as choosing the correct shaft flexion like so many golfers; even many fitters are mistaken!
How to reshaft a golf club?
In case players want to replace the new golf shaft at home, you should carefully read the instructions for use and know the most accurate replacement technique. Here are pretty simple technical tutorials for your reference.
First, you need to know what kind of shaft is right for you. There are many different golf shafts available to each player. Choosing the right golf shaft will help us get the perfect shot.
Please also note that make sure your new shaft is the same size as the old club shaft, matching the size of the Hosel part at the tip of the club. Hosel is the intersection point of the shaft tip and the center of the clubhead. If there is no dimension on the shaft label, you can use the identification gauge to check the dimensions.
Specific steps to change shaft:
Step 1: Use a paper-knife
it is to scrape off the metal tube at the bottom of Hosel. Then, place the golf club on the Grip shaft to fix the shaft during shaft replacement. Note when performing this operation to avoid the blade facing the body. Otherwise, it may cause injury.
Next, pull out the old grip and erase the glue around the tail shaft. Then heat Hosel’s surroundings to let the Epoxy glue connect the clubhead to the soft shaft.
Finally, wait at least 30 minutes for the glue to dry before using it completely. If in a hurry, it is easy to cause them to flake off again.
With the old grip, it’s a little more complicated. The golfer must use a dedicated clamp or something else to keep the club in place horizontally. This makes taking out the old grip more convenient. Of course, without both, using hands is a possible last resort, though a bit difficult.
Step 2: Use the lift bar to push into the base of the Hosel
This way helps the shaft release the tip of the club. Once the shaft and clubhead are separated, let the clubhead cool completely before mounting the new shaft. Use a clean towel to wipe all the old Epoxy adhesive from Hosel.
Step 3: Remove the paint from the replacement
To remove the paint from the replacement shaft tip completely, you can either use sandpaper or use a small knife. You will probably have to shave off an extra coating on the clubhead if the shaft type you use for the club is Graphite.
Step 4: Take the Epoxy adhesive
Next, we take the Epoxy adhesive on the top of the shaft and insert the shaft into the hole at the bottom of Hosel. You rotate the shaft to the right and left a few times so that the glue can cover the inner surface of Hosel, and the shaft will ensure stability.
Step 5: Remove the Grip on the shaft
You remove the Grip on the old golf club’s shaft and use Epoxy glue to attach it to the new shaft. We wipe Hosel off to remove any excess glue. It is recommended to let the glue dry for a few hours before you use the stick.
Wrap the dedicated 2-sided tape with a length of about 25 cm to cover the entire tail shaft, avoiding dust and dirt. Next, spray the solvent chemical layer over the tape and inside the new grip. It will help remove impurities such as old glue, dirt leftover. It is cleaning the surface of the stick, helping the glue stick more when sticking.
To complete the final step, you just have to fill the prepared new grip with the grip’s shaft. If more meticulous, the golfer can logo the brand upwards when the clubface is perpendicular. Both increase the aesthetics and easily align when performing a shot. Of course, you still have to wait for the glue to dry before you use it.
Through this article about “How to reshaft a golf club?”, customers have basic information on old stick shaft replacement rates and home replacement instructions. Customers who self-replace shaft should pay close attention to thoroughly understand the type of shaft you will use, choose reputable accessories suppliers to have genuine products.
Hopefully, through this article, you can save time and effort for the replacement of golf accessories which is specifically the shaft of the golf club.